Martin MAC 2000 Wash Bedienungsanleitung PDF herunterladen (Seite 36)

36 MAC 2000 Wash

ISPLAY

MESSAGES

Message Appears when... What to do

RST (Reset) ... the fixture is indexing effects at startup. Wait for reset to complete.

SRST (Serial reset)

... the fixture has received a reset command

from the controller.

Wait for reset to complete. Set

PERS/dRES to off to prevent accidental

reset commands.

HOME ... the effects have been indexed and are

moving to their default positions.

Wait a few moments.

OPEN

...the lamp access cover is not fully closed.

Verify that the lamp access cover is locked

in place.

LERR (Lamp error) ... the lamp doesn’t ignite within 10 minutes of

receiving the ‘Lamp ON’ command. Likely

reasons are a missing or defective lamp, or

insufficient AC voltage.

Check the lamp. Check that the voltage

and frequency settings match the local

supply.

MERR (Memory error)

...the EEPROM memory cannot be read.

Contact Martin service personnel for

assistance.

ShER (Short error) ... the fixture detects the lamp is ON but no

‘Lamp ON’ command has been received. This

can occur if the lamp relay is stuck or if the

lamp-power feedback circuit fails. The fixture

may be operated but remote lamp on/off may

be effected.

Contact Martin service personnel for

assistance.

bTER (Base temperature error)

HTER (Head temperature error)

... there is a fault with the temperature sensor

in the base or head.

Contact Martin service personnel for

assistance.

FbEP (Feedback error pan)

FbET (Feedback error tilt)

FbER (Feedback error pan/tilt)

...pan (FbEp), tilt (FbET) or both (FbER)

feedback circuits are malfunctioning. It will still

be possible to operate the fixture, though it

goes into a “safe” mode where maximum

speed is reduced, thus preventing the fixture

from losing track of its home position (losing

step).

Contact Martin service personnel for

assistance.

PAER (Pan time-out)

TIER (Tilt time-out)

CYER (Cyan time-out)

MAER (Magenta time-out)

YEER (Yellow time-out)

CTER (CTC time-out)

COER (Color wheel 1)

C2ER (Color wheel 2 time-out)

ZOER (Zoom time-out)

...the electric indexing circuit is

malfunctioning. The fixture will, after the

time-out, establish a mechanical stop, and

continue to work normally.

Reset fixture again. Contact Martin

service personnel if problem continues.

RBER ...the barn door rotation mechanism is

malfunctioning.

Reset fixture again. Contact Martin

service personnel if problem continues.

S3SC

S4SC

S5SC

S6SC

S7SC

S8SC

S9SC

S10S

S11S

S12S

...an effect does not move away from the index

position under reset, a sensor or micro-switch

circuit is shorted, or a micro-switch is stuck or

connected incorrectly.

Contact Martin service personnel for

assistance.

RAME ...there is an on board RAM memory error. Contact Martin service personnel for

assistance.

OPER ...there is an on-board programming error. Contact Martin service personnel for

assistance.

L1ER

...light sensor 1 is in error status.

Contact Martin service personnel for

assistance.

LTE R

...lamp temperature error.

Set the fan speed to FULL using the UTIL

menu and restart the fixture. Contact

Martin service personnel if problem

persists.

THER ---there is a thermoswitch error or a jumper on

PL47 error.

Contact Martin service personnel for

assistance.

Table 2: Display messages

1 2 ... 31 32 33 34 35 36 37 38 39 40 41

Kommentare zu diesen Handbüchern

Keine Kommentare

Martin MAC 2000 Wash Bedienungsanleitung Seite 36

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Flutlichter Martin MAC 2000 Wash