Martin MAC 500E Wartungshandbuch

MAC 500service manual

1998-08-038 MAC 5001. Remove the rotating-gobo wheel.2. Refer to Figure 2-3. Remove the outer ring (T).3. Remove the retaining spring (not shown) from

1998-08-03 9Parts Removal and Installation2. Refer to Figure 2-4. Through the open gobo in the fixed gobo wheel, remove the 2 screws (A) from the rear

1998-08-0310 MAC 5005. Thread the focus belt over the back roller, under the motor, and over the front roller. Stretch the belt to the posi-tion you m

1998-08-03 11Parts Removal and Installation2.10.2 CONFIGURE XLR PIN-OUT AND BOOT SET-TING JUMPERS1. Position the jumpers for the desired XLR pin-out o

1998-08-0312 MAC 5003. Slip the old belt off the pan drive gear first, them off the pan motors, and remove.4. Guide the new belt over the wires, yoke

1998-08-03 13Parts Removal and Installation2.14CONTROL MODULE2.14.1 REPLACE1. Remove the main circuit board. Remove the 4 nuts from the back of the co

1998-08-0314 MAC 500 section 3ADJUSTMENT3.1 INDEXING METHODSEffects indexing in the MAC 500 is determined by one of three methods. The adjustment proc

1998-08-03 15Adjustment5. Center the effect in the light path. Begin by visually centering the effect with the lamp off. Then strike the lampand focus

1998-08-0316 MAC 5006. Repeat steps 3 and 4 for color wheel 1. 7. Use the control panel to test alignment at a number of positions. When the wheels ar

1998-08-03 17Adjustment3.11OPTIMIZING LAMP ALIGNMENT1. Disconnect the fixture from AC power supply and allow the lamp to cool.2. Make a preliminary ad

© 1997, 1998 Martin Professional A/S, Denmark.All rights reserved. No part of this manual may bereproduced, in any form or by any means, withoutpermis

1998-08-0318 MAC 500 section 4TROUBLESHOOTING4.1 GENERAL4.1.1 FIXTURE DOES NOT RESET• Blown fuse: LEDs on the printed circuit board light up to indica

1998-08-03 19Troubleshootingthe lamp circuit on, measure the voltage across the heavy blue and black wires at the connection block. The reading should

1998-08-0320 MAC 5004.6 GOBOS4.6.1 FIXED-GOBO WHEEL STARTS ROTATING SPONTANEOUSLY• Improper adjustment: This can occur when the fixture reaches operat

1998-08-03 21Troubleshootingeffect but is most visible when it affects the shutter. Install version 1.4. 4.8.2 SHUTTER/DIMMER LOSES STEP, CAUSING LIGH

1998-08-0322 MAC 500 section 5SOFTWARE LOG Version & Date Changes1.698/7/31• "MERR" problem solved. Some fixtures were subject to a p

1998-08-03 23Software Log1.097/10/1• DMX protocol version 2 implemented. • Martin protocol implemented.• 65 combined colors implemented on one DMX cha

1998-08-0324 MAC 500 section 6MAJOR HARDWARE CHANGES S/N forImplementation Changes980515-000Harder dimmer/shutter The dimmer/shutter blade with ada

1998-08-03 25Major Hardware Changes971219-000New head shellThe plastic in the shell of the MAC 500 head was changed to another type that withstands hi

1998-08-0326 MAC 500 section 7TYPICAL SPARE PARTS7.1 911360-000000 MAC 500 IN CARDBOARD; 230V,50HZ ; ; MSR 575 ; BLACK180010-010000 MAC 500/600, Keybo

1998-08-03 27Typical Spare Parts337750-000000 Magnet 2x2x2 mm339020-000000 Stepmotor standard small , wire 700mm 125deg339021-000000 Stepmotor stand

03-08-1998 1MAC 500 section 1INTRODUCTIONABOUT THIS MANUAL ...

1998-08-0328 MAC 500375206-000000 Iris 49mm molykote on leaves375301-000000 Prism Asph/plano D= 47 , 3 facets376470-000000 Color Wheel 1 MAC 500

1998-08-03 29Block Diagram section 8BLOCK DIAGRAM

1998-08-032 MAC 500 section 1INTRODUCTION1.1 ABOUT THIS MANUAL1.1.1 PURPOSESince its introduction at PLASA in the fall of 1997, the MAC 500 has proven

1998-08-03 3Introduction1.3 ADDITIONAL CAUTIONS1.3.1 ELECTROSTATIC DISCHARGE (ESD) SENSITIVE PARTSThe following parts are classified as ESD sensitive:

1998-08-034 MAC 500 section 2PARTS REMOVAL AND INSTALLATION2.1 LOCTITE THREAD LOCK 2.1.1 EXTENT OF APPLICATION Loctite thread lock is used on all mach

1998-08-03 5Parts Removal and Installation6. Remove the tilt-sensor circuit board.7. Remove the bottom row of 5 screws from both sides of the yoke bas

1998-08-036 MAC 5002.4 COLOR WHEEL MODULE2.4.1 REMOVE MODULE1. Refer to figure Figure 2-1. Working from the top of the head, remove the top air flow p

1998-08-03 7Parts Removal and Installation2. Loosen the 2 set screws on the adaptor (H) and pull off the wheel.2.5.5 INSTALL FIXED-GOBO WHEEL1. Remove