Martin MAC 250 ENTOUR Bedienungsanleitung

MAC 250 Washuser manual

10 MAC 250 Wash5. Install a safety cable that can bear at least 10 times the weight of the fixture securely to the structure and anchor the cable to

Control panel 11Control panelYou can set the MAC 250 Wash’s DMX address, configure individual fixture settings (personality), read out data, and exec

12 MAC 250 Wash• , the pan and tilt invert menu, allows you to swap the pan and tilt channels (→), invert pan movement (→), and inver

Control panel 13settings are overridden. The message  scrolls in the display if you try to change speed settings via the  or 

14 MAC 250 Wash displays the DMX start code. Packets with a start code other than 0 may cause irregular performance. The remaining readouts under

Control panel 15Lamp power and reset shortcutsThe control panel buttons can be used to control lamp power and reset the fixture.• To strike the lamp,

16 MAC 250 WashDMX controlThe MAC 250 Wash is compatible with USITT DMX 512 controllers and can be added to a standard DMX data link.This section bri

DMX control 17COLORThe color wheel can be scrolled continuously – allowing for split color effects – or in steps, and rotated randomly or continuousl

18 MAC 250 WashOpticsColor filtersSTANDARD CONFIGURATIONThe MAC 250 Wash provides 6 dichroic color filters as shown below. REPLACING A COLOR FILTERDa

Optics 193. Put on clean lint-free gloves or use a clean lint-free cloth to avoid having to clean filters after handling.4. Turn the color wheel to a

DimensionsAll measurements are expressed in millimeters393538469364119315270°270°560270°128.5°128.5°Min. c/c 410Min. c/c 410375© 2005 Martin Professio

20 MAC 250 WashInstalling the wide-angle lensA 61.5° cutoff-angle wide-angle lens is supplied with the MAC 250 Wash, together with all items necessar

Service 21ServiceThe MAC 250 Wash requires regular maintenance to maintain peak performance. Refer any service that is not described here to a profes

22 MAC 250 WashINSTALLING A LAMPDanger! Intense heat. Avoid contact by persons and materials. The exterior of the fixture can get very hot – up to 16

Service 233. Remove the head covers using a flathead screwdriver to loosen the four quarter-turn screws. 4. Release the air filter from the lower cov

24 MAC 250 WashReplacing fusesMAIN FUSEThe main fuse holder is built into the mains input socket.Warning! Always replace the fuse with one of the sam

Service 25NORMAL UPDATETo update fixture software, connect an upload device to the fixture just like a DMX controller and perform a DMX mode upload a

26 MAC 250 WashDMX protocolChannel – 16 Bt(16-Bit Mode)Channel – 16 Ex(16-bit Extended) Value Percent Function1 1a. If DMX Reset is

DMX protocol 276100 - 1790265177102128153180 - 183184 - 187188 - 191192 - 195196 - 199200 - 203204 - 207208 - 226227 - 245246 - 248249 - 251252 - 255

28 MAC 250 WashControl menu Factory default settings are shown in bold type.Menu Item Options Notes (default settings in bold print) - (16-bi

Control menu 29 Return all personality settings (not calibrations) to factory defaultsLoad custom configuration 1Save custom

ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 MAC 250 WashReset fixtureLamp onLamp offOpen shutterClose shutterFast strobeMedium strobeSlow strobe -

Control menu 31Adjustment submenuThis menu is accessed in →. Factory default settings are shown in bold type.Control panel shortcuts• To strik

32 MAC 250 WashError messagesDisplay readout Appears if... What to do...there is no communication between the control panel and motherboard (t

Troubleshooting 33TroubleshootingProblem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture. • Check that pow

34 MAC 250 WashCircuit board connectionsDisableEnable

MAC 250 Wash SpecificationsPHYSICALBase length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAC 250 Wash wide-angle lens with frostTotal output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPROVALSEU EMC . . . . . . . . . . . . . . . EN 55 103-1, EN 55 015, EN 61 547EU safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

This page is intentionally left blank

Introduction 5IntroductionThank you for selecting the Martin MAC 250 Wash, a moving head wash light with a range of color-changing and control option

6 MAC 250 Wash• Check that power supply settings match the local AC power before use.• Do not expose the fixture to rain or moisture. • Refer any ser

Setup 7SetupUnpackingThe MAC 250 Wash is supplied with:• MSD 250/2 lamp (factory installed)• 3-meter, 3-wire IEC power cable• Wide-angle lens• This u

8 MAC 250 WashCONFIGURING FOR LOCAL AC POWER1. Disconnect the fixture from power. 2. Remove the 2 Phillips screws in the access cover directly behind

Setup 92. Plug the prepared power cable into the AC input socket and a grounded (earthed) AC power outlet. InstallationLOCATION AND ORIENTATIONThe MA