Mania PR1user manual
10 Mania PR1 user manualInstalling a plug on the mains leadWarning! For protection from dangerous electric shock, the fixture must be grounded (earth
Installation 11Warning! Block access below the work area before proceeding. Always use a secure means of secondary attachment. For indoors use only.T
12 Mania PR1 user manualOPERATION3The lamp will light when the mains switch at the rear of the fixture is turned on.Important! This fixture is designe
Operation 133 Lift the gobo holder out of the fixture.4 The gobo/texture glass is held in place by a steel spring. Remove the spring to remove the gob
14 Mania PR1 user manual INSTALLING A COLOR FILTERYou can install a color filter in the slot that can be found on the lamp side of the gobo holder. Th
Operation 15 GOBO ROTATIONYou can adjust the speed and direction of the gobo rotation using the controls at the rear of the fixture. REMOTE CONTROL OP
16 Mania PR1 user manualBASIC SERVICE4This chapter describes the maintenance procedures that you can perform yourself.Warning The exterior of the fixt
Basic service 172 Remove the thumb screw holding the cover in place.3 Slide the fixture cover open.4 Vacuum or gently blow away dust and loose particl
18 Mania PR1 user manuallamp type may damage the fixture and will invalidate the product warranty.Installing a lamp in the Mania PR11 Disconnect the f
Basic service 195 Replace the bulb. Use only a Philips 6958 24V 250W 10H lamp (Martin P/N 97000115). Warning Installing any other lamp may damage the
Measurements are expressed in millimeters.340158315290Ø13© 2003-2004 Martin Professional A/S, Denmark.All rights reserved. No part of this manual ma
20 Mania PR1 user manual5. The lens module has a bayonet-type fitting. Working through the front aperture of the fixture, loosen – but do not remove –
Basic service 217. Prepare a soft cloth or similar device to catch components if they fall out of the lens module.8. See illustration below. Open the
22 Mania PR1 user manual LENS ASSEMBLYWhen you open the Mania PR1 lens module, you may find out the hard way that it is easy to mix up the lenses. To
Troubleshooting 23TROUBLESHOOTING5problem probable cause(s) suggested remedyNo light No power to the fixture Check connectionsBlown fuse If power is a
SPECIFICATIONSAPHYSICALSize without mounting bracket (LxWxH). . .340x290x158 mm (13.4x11.4x6.2 in.)Weight. . . . . . . . . . . . . . . . . . . . . . .
Specifications 25TYPICAL POWER AND CURRENT115 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 W, 2.
www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010
3Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Safety information . . . . . .
4 Mania PR1 user manual
Introduction 5INTRODUCTION1Thank you for selecting a Martin Mania PR1. The Mania PR1 is a gobo projector with a motorized rotating gobo. Gobo rotation
6 Mania PR1 user manualShields, lenses or ultraviolet screens must be changed if they become visibly damaged to the extent that their effectiveness is
Introduction 7Preventing injuries due to falls• When suspending the fixture above ground level, verify that the structure can hold at least 10 times t
8 Mania PR1 user manual MANIA PR1 OVERVIEWCooling ventSafety cable attachment eyeAC supply settingMains switchMains socketFuse holderCooling fanThumb
Installation 9INSTALLATION2 AC POWERBefore operation, ensure that factory setting of voltage and frequency match local power supply. Always ground (ea
Kommentare zu diesen Handbüchern