MAC 250 Washuser manualTM
10 MAC 250 Wash5. Install a safety cable that can bear at least 10 times the weight of the fixture securely to the structure and anchor the cable to
Control panel 11Control panelYou can set the MAC 250 Wash’s DMX address, configure individual fixture settings (personality), read out data, and exec
12 MAC 250 Wash• , the pan and tilt invert menu, allows you to swap the pan and tilt channels (→), invert pan movement (→), and inver
Control panel 13settings are overridden. The message scrolls in the display if you try to change speed settings via the or
14 MAC 250 Wash displays the DMX start code. Packets with a start code other than 0 may cause irregular performance. The remaining readouts under
Control panel 15Lamp power and reset shortcutsThe control panel buttons can be used to control lamp power and reset the fixture.• To strike the lamp,
16 MAC 250 WashDMX controlThe MAC 250 Wash is compatible with USITT DMX 512 controllers and can be added to a standard DMX data link.This section bri
DMX control 17COLORThe color wheel can be scrolled continuously – allowing for split color effects – or in steps, and rotated randomly or continuousl
18 MAC 250 WashOpticsColor filtersSTANDARD CONFIGURATIONThe MAC 250 Wash provides 6 dichroic color filters as shown below. REPLACING A COLOR FILTERDa
Optics 193. Put on clean lint-free gloves or use a clean lint-free cloth to avoid having to clean filters after handling.4. Turn the color wheel to a
DimensionsAll measurements are expressed in millimeters©2005-2008 Martin Professional A/S. Information subject to change without notice. Martin Profes
20 MAC 250 WashInstalling the wide-angle lensA 61.5° cutoff-angle wide-angle lens is supplied with the MAC 250 Wash, together with all items necessar
Service 21ServiceWarning! Read “Safety information” on page 5 before servicing the MAC 250 Wash. Disconnect the fixture from power and allow to cool
22 MAC 250 WashLamp replacementLamp life will vary. The rated life of a lamp is the average operating life before lamp failure in the manufacturer’s
Service 237. Align the screw holes and fasten the lamp access plate with 2 screws. 8. If installing a new lamp, reset the lamp hour and lamp strike c
24 MAC 250 Wash11. Remove the two 4mm Allen screws from the carrying handles on the sides of the base unit and remove the louvered side covers. Clean
Service 253. Carefully remove and check the two fuses located in the bottom of the PCB (see “Circuit board connections” on page 34). Replace as neces
26 MAC 250 WashDMX protocolChannel – 16 Bt(16-Bit Mode)Channel – 16 Ex(16-bit Extended) Value Percent Function1 1a. If DMX Reset is
DMX protocol 276100 - 1790265177102128153180 - 183184 - 187188 - 191192 - 195196 - 199200 - 203204 - 207208 - 226227 - 245246 - 248249 - 251252 - 255
28 MAC 250 WashControl menu Factory default settings are shown in bold type.Menu Item Options Notes (default settings in bold print) - (16-bi
Control menu 29 Return all personality settings (not calibrations) to factory defaultsLoad custom configuration 1Save custom
ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30 MAC 250 WashReset fixtureLamp onLamp offOpen shutterClose shutterFast strobeMedium strobeSlow strobe -
Control menu 31Adjustment submenuThis menu is accessed in →. Factory default settings are shown in bold type.Control panel shortcuts• To strik
32 MAC 250 WashError messagesDisplay readout Appears if... What to do...there is no communication between the control panel and motherboard (t
Troubleshooting 33TroubleshootingProblem Probable cause(s) RemedyOne or more of the fixtures is completely dead.No power to fixture. • Check that pow
34 MAC 250 WashCircuit board connectionsDMXDMXDisableEnable
MAC 250 Wash™ Specifications 35MAC 250 Wash™ SpecificationsPHYSICALBase length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36 MAC 250 WashMAC 250 Wash standard with frostTotal output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAC 250 Wash™ Specifications 37FusesMain fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 A / 250 V, time-delay – P/N 05
38 MAC 250 WashORDERING INFORMATIONMAC 250 Wash™ (in cardboard box) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90225810
Disposing of this productMartin™ products are supplied in compliance with Directive 2002/96/EC of the European Parliament and of the Council of the Eu
www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010
Introduction 5IntroductionThank you for selecting the Martin™ MAC 250 Wash™, a moving head wash light with a range of color-changing and control opti
6 MAC 250 Wash• Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fa
Setup 7SetupUnpackingThe MAC 250 Wash is supplied with:• MSD 250/2 lamp (factory installed)• 3-meter, 3-wire IEC power cable• Wide-angle lens• This u
8 MAC 250 WashCONFIGURING FOR LOCAL AC POWER1. Disconnect the fixture from power. 2. Remove the 2 Phillips screws in the access cover directly behind
Setup 92. Plug the prepared power cable into the AC input socket and a grounded (earthed) AC power outlet. InstallationLOCATION AND ORIENTATIONThe MA
Kommentare zu diesen Handbüchern